← All lessons
Electrical · Kraken X60 · Kraken X44 · Talon FX

Feed the Kraken.

A Kraken can turn battery power into a lot of motion. Your job is to get that power there cleanly, keep every connection tight, and stop extra current from becoming extra heat.

power deliveredpower wasted as heatCAN datasafe limit
Part 1 / What is inside the can?

The controller travels with the motor

The Kraken X60 and smaller X44 are brushless motors with an integrated Talon FX controller and encoder. The power distribution board feeds the Kraken directly, while the CAN bus tells its onboard controller what to do.

Red and black carry energy. Yellow and green carry messages. Mixing up those jobs is a fast way to have a robot that either does nothing or releases the expensive smoke.

12 V batteryenergy source 6 AWG120 A mainbreaker PDH / PDPone protectedbranch per Kraken 10 AWGKraken X60 / X44Talon FX + motorinside one housing roboRIO 22 AWG twisted CAN pair
Two paths, two jobs. Battery → main breaker → power distribution → one protected branch → Kraken carries power. The roboRIO's CAN bus carries commands and telemetry.
Before plugging in the battery: inspect polarity end to end, put the robot on blocks, and have a second person check. Give every Kraken its own correctly protected power-distribution branch—never daisy-chain motor power from one Kraken to the next.
Part 2 / Share the source

Power distribution is a budget, not a buffet

A branch breaker protects the branch wiring; it does not promise the motor only ever sees the number printed on the breaker. FRC thermal breakers can pass higher current for short bursts. Several motors also add together at the battery, where total current causes voltage sag and can pull the whole robot toward a brownout.

Widget 01 — The power budgetbattery + branches
Total motor current
160 A
Battery under load
9.2 V
Robot state

Try 1: Hold 40 A and move from one motor to eight—the branch current stays the same, but the battery sees the sum. Try 2: Use four motors at 80 A; a breaker may allow a brief burst, but voltage collapses quickly in this teaching model. Current limits and smooth acceleration protect the whole robot.

Itotal = I1 + I2 + ... + In
Vloaded = Vopen - ItotalRbattery
I_total total current demanded from the batteryI_1 ... I_n current in each motor branchV_loaded battery voltage while workingV_open battery voltage with almost no loadR_battery effective internal resistance of the battery and main pathThe widget uses 12.4 V and 0.020 Ω to teach the relationship—not to grade a real battery.
Part 3 / Four wires, two jobs

Put each color exactly where it belongs

The two power wires feed the Talon FX inside the Kraken. The two CAN wires carry commands and telemetry. Keep the jobs separate: power goes from a protected PDH/PDP branch to the Kraken; CAN continues through the robot's CAN chain.

Widget 02 — Wiring mappower + CAN terminals
Wire colors
red + black
Connect to
+ and − power terminals
CTRE preset-driver bit
T10

Power: use the red 10 AWG lead from the positive PDH/PDP output to the Kraken's positive power terminal, and the black lead from the negative output to the negative terminal. Use the CTRE preset torque driver with a T10 bit. Follow the terminal markings—never trust wire location alone.

Terminal habit: start every screw by hand, keep the ring terminal flat against the terminal, then let the preset torque driver click. Use the supplied-length terminal screw or the hardware documented for an approved adapter; a longer screw can damage the controller.
Part 4 / Wire is part of the circuit

A smaller gauge number means a bigger copper path

American Wire Gauge (AWG) runs backwards: 10 AWG is thicker than 12 AWG, which is thicker than 14 AWG. Thicker copper has less resistance. Less voltage is lost before it reaches the Kraken, and less power is cooked into the wire.

Widget 03 — Wire-gauge labvoltage drop + heat
Voltage lost
0.32 V
Wire heating
12.8 W
At the Kraken
11.68 V

Try 1: Compare all three gauges at 40 A. Try 2: Double current: voltage drop doubles, but heating becomes four times larger. Try 3: Double cable length; current travels out on red and back on black, so the calculation uses both conductors.

Vdrop = I · R
Pheat = I² · R
V_drop voltage lost along both power conductorsI current flowing through the branchR resistance of the complete red-and-black wire loopP_heat electrical power turned into heat in the wireThe square is the trap: twice the current produces four times the resistive heating.

Kraken wire bundles use 10 AWG power leads to reduce resistance and voltage drop. Use wiring and protection permitted by the current FRC rules, make sound crimps, keep runs short, and add strain relief near the terminals.

Part 5 / Current becomes temperature

Torque is useful. Heat is the bill.

Near stall, a motor turns slowly while pulling enormous current. Very little electrical power becomes motion, so much more becomes heat in the windings and controller. A brief launch is one thing; holding a jammed intake, arm, or drivetrain against a wall keeps paying that heat bill every second.

Widget 04 — Thermal benchcomparative teaching model
Plot — temperature since reset

The dashed line marks the model's thermal-cutoff region. Real temperature depends on mechanism, duty cycle, airflow, ambient conditions, firmware, and where temperature is measured.

Current applied
80 A
Temperature
25 °C
Motor state

Try 1: Request 160 A with a 60 A limit—the limit caps torque and slows heating. Try 2: Raise the limit while it runs. Try 3: Compare X60 and X44; the smaller X44 model heats faster because it has less thermal mass. This illustrates the trend, not an exact factory curve.

Pcopper = Istator² · Rwinding
P_copper heat produced in the motor windingsI_stator motor-side current that creates torqueR_winding electrical resistance of the motor windingsCTRE notes that stator limits restrict torque, reduce heat buildup, and can also reduce supply current during acceleration.
Why overheating is bad: hot copper has more resistance, so efficiency falls. Repeated or extreme heat ages insulation, bearings, magnets, solder joints, and electronics. The Talon FX can enter thermal cutoff, meaning lost motor output exactly when the robot is under stress. A current limit is cheaper than a cooked mechanism—or a dead match.
Part 6 / Pit checklist

Five ideas to walk away with

1. Give each Kraken a clean, protected branch from the power distribution board. 2. Use red/black 10 AWG power wiring where specified, keep it short, and make high-quality terminations. 3. Keep yellow/green CAN as a twisted pair, and use the CTRE preset driver with a T10 bit for power terminals or a T8 bit for CAN terminals. 4. Set current limits for the mechanism, not for bragging rights. 5. Log supply current, stator current, voltage, and temperature—heat is a symptom you can see coming.

Pocket glossary
Power branch one protected path from the PDH/PDP to one loadAWG wire-size system where a smaller number means thicker wireVoltage drop voltage lost across resistance before reaching the loadSupply current current drawn from the battery side of the Talon FXStator current motor-side current closely tied to torque and winding heatThermal cutoff protective shutdown when the controller becomes too hot

Official references: WCP Kraken wiring and terminal specifications, CTRE Talon FX hardware guidance, and WPILib wiring best practices. Always check the current FRC game manual before final robot inspection.